X-Git-Url: https://git.shemshak.org/~bandali/configs/blobdiff_plain/4e67332096605cb669f0eae557d16d2d6a2f7d18..9494231456fe472e24edd88d79b87c87aff5350a:/other/tlp/etc/default/tlp

diff --git a/other/tlp/etc/default/tlp b/other/tlp/etc/default/tlp
index 44638d2..9b411e3 100644
--- a/other/tlp/etc/default/tlp
+++ b/other/tlp/etc/default/tlp
@@ -1,5 +1,5 @@
 # ------------------------------------------------------------------------------
-# tlp - Parameters for power save
+# tlp - Parameters for power saving
 # See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html
 
 # Hint: some features are disabled by default, remove the leading # to enable
@@ -12,6 +12,10 @@ TLP_ENABLE=1
 # Concerns some desktop and embedded hardware only.
 TLP_DEFAULT_MODE=AC
 
+# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
+# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC
+TLP_PERSISTENT_DEFAULT=0
+
 # Seconds laptop mode has to wait after the disk goes idle before doing a sync.
 # Non-zero value enables, zero disables laptop mode.
 DISK_IDLE_SECS_ON_AC=0
@@ -35,33 +39,40 @@ MAX_LOST_WORK_SECS_ON_BAT=60
 #   You *must* disable your distribution's governor settings or conflicts will
 #   occur. ondemand is sufficient for *almost all* workloads, you should know
 #   what you're doing!
-#CPU_SCALING_GOVERNOR_ON_AC=powersave
-#CPU_SCALING_GOVERNOR_ON_BAT=powersave
+CPU_SCALING_GOVERNOR_ON_AC=performance
+CPU_SCALING_GOVERNOR_ON_BAT=powersave
 
 # Set the min/max frequency available for the scaling governor.
 # Possible values strongly depend on your CPU. For available frequencies see
 # the output of tlp-stat -p.
-#CPU_SCALING_MIN_FREQ_ON_AC=0
-#CPU_SCALING_MAX_FREQ_ON_AC=0
-#CPU_SCALING_MIN_FREQ_ON_BAT=0
-#CPU_SCALING_MAX_FREQ_ON_BAT=0
+CPU_SCALING_MIN_FREQ_ON_AC=800000
+CPU_SCALING_MAX_FREQ_ON_AC=3300000
+CPU_SCALING_MIN_FREQ_ON_BAT=800000
+CPU_SCALING_MAX_FREQ_ON_BAT=3300000
+
+# Set energy performance hints (HWP) for Intel P-state governor:
+#   default, performance, balance_performance, balance_power, power
+# Values are given in order of increasing power saving.
+# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
+CPU_HWP_ON_AC=balance_performance
+CPU_HWP_ON_BAT=balance_power
 
 # Set Intel P-state performance: 0..100 (%)
 # Limit the max/min P-state to control the power dissipation of the CPU.
 # Values are stated as a percentage of the available performance.
 # Requires an Intel Core i processor with intel_pstate driver.
-#CPU_MIN_PERF_ON_AC=0
-#CPU_MAX_PERF_ON_AC=100
-#CPU_MIN_PERF_ON_BAT=0
-#CPU_MAX_PERF_ON_BAT=30
+CPU_MIN_PERF_ON_AC=0
+CPU_MAX_PERF_ON_AC=100
+CPU_MIN_PERF_ON_BAT=0
+CPU_MAX_PERF_ON_BAT=100
 
 # Set the CPU "turbo boost" feature: 0=disable, 1=allow
 # Requires an Intel Core i processor.
 # Important:
 # - This may conflict with your distribution's governor settings
 # - A value of 1 does *not* activate boosting, it just allows it
-#CPU_BOOST_ON_AC=1
-#CPU_BOOST_ON_BAT=0
+CPU_BOOST_ON_AC=1
+CPU_BOOST_ON_BAT=1
 
 # Minimize number of used CPU cores/hyper-threads under light load conditions
 SCHED_POWERSAVE_ON_AC=0
@@ -155,18 +166,18 @@ WIFI_PWR_ON_BAT=on
 WOL_DISABLE=Y
 
 # Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
-# A value of 0 disables, >=1 enables power save.
+# A value of 0 disables, >=1 enables power saving.
 SOUND_POWER_SAVE_ON_AC=0
 SOUND_POWER_SAVE_ON_BAT=1
 
 # Disable controller too (HDA only): Y/N
 SOUND_POWER_SAVE_CONTROLLER=N
 
-# Set to 1 to power off optical drive in UltraBay/MediaBay when running on
-# battery. A value of 0 disables this feature (Default).
+# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
 # Drive can be powered on again by releasing (and reinserting) the eject lever
 # or by pressing the disc eject button on newer models.
 # Note: an UltraBay/MediaBay hard disk is never powered off.
+#BAY_POWEROFF_ON_AC=0
 #BAY_POWEROFF_ON_BAT=0
 # Optical drive device to power off (default sr0).
 #BAY_DEVICE="sr0"
@@ -175,33 +186,39 @@ SOUND_POWER_SAVE_CONTROLLER=N
 RUNTIME_PM_ON_AC=on
 RUNTIME_PM_ON_BAT=auto
 
-# Runtime PM for *all* PCI(e) bus devices, except blacklisted ones:
-#   0=disable, 1=enable
-RUNTIME_PM_ALL=1
-
 # Exclude PCI(e) device adresses the following list from Runtime PM
 # (separate with spaces). Use lspci to get the adresses (1st column).
 #RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"
 
-# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM
-# (should prevent accidential power on of hybrid graphics' discrete part).
-# Default is "radeon nouveau"; use "" to disable the feature completely.
+# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
+# Default when unconfigured is "amdgpu nouveau nvidia radeon" which
+# prevents accidential power-on of dGPU in hybrid graphics setups.
+# Use "" to disable the feature completely.
 # Separate multiple drivers with spaces.
-RUNTIME_PM_DRIVER_BLACKLIST="radeon nouveau"
+#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"
 
 # Set to 0 to disable, 1 to enable USB autosuspend feature.
 USB_AUTOSUSPEND=1
 
 # Exclude listed devices from USB autosuspend (separate with spaces).
 # Use lsusb to get the ids.
-# Note: input devices (usbhid) are excluded automatically (see below)
+# Note: input devices (usbhid) are excluded automatically
 #USB_BLACKLIST="1111:2222 3333:4444"
 
-# WWAN devices are excluded from USB autosuspend: 0=do not exclude / 1=exclude
-#USB_BLACKLIST_WWAN=1
+# Bluetooth devices are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude
+USB_BLACKLIST_BTUSB=0
+
+# Phone devices are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude (enable charging)
+USB_BLACKLIST_PHONE=0
+
+# WWAN devices are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude
+USB_BLACKLIST_WWAN=1
 
 # Include listed devices into USB autosuspend even if already excluded
-# by the driver or WWAN blacklists above (separate with spaces).
+# by the blacklists above (separate with spaces).
 # Use lsusb to get the ids.
 #USB_WHITELIST="1111:2222 3333:4444"
 
@@ -251,6 +268,9 @@ RESTORE_DEVICE_STATE_ON_STARTUP=0
 #START_CHARGE_THRESH_BAT1=75
 #STOP_CHARGE_THRESH_BAT1=80
 
+# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable
+#RESTORE_THRESHOLDS_ON_BAT=1
+
 # ------------------------------------------------------------------------------
 # tlp-rdw - Parameters for the radio device wizard
 # Possible devices: bluetooth, wifi, wwan